So running the calibration tool is pretty easy, just follow the included directions but note, on a dual monitor setup run it on your primary monitor first. The one marked “1” in the display settings. After the tool completes its going to install an application that runs on startup and makes sure the correct profile is loaded. This profile will be put in the directory I stated above. Now after this is done, go into that directory and rename the profile. I renamed mine from Spyder2Express.icm to Spyder2Express_right.icm and when I do the left monitor I will rename that one ‘_left’.

After this you’ll want to take your monitors and switch the primary monitor to your secondary. This way you can run the software on the other monitor now. Restart the machine and once the new primary monitor is set run the Spyder2Express again. This profile will be in that same directory with the default name again. Rename this one to something, i.e. “_left”. And you’re done with the calibration tool.

Now after this I go into our color control software, be it Vista’s built in software or our downloaded applet for XP, and I select one of the monitors listed (if you have different makes and models this will be easy, if they are the same it’s a bit of guesswork) and associate it with one of the profiles made, either the _right or the _left profile. Now select the other monitor and associate with the other profile. After applying these changes restart your machine. When the Spyder2Express Software loads up you *should* see a message on each screen where it is loading up the color profile. Now in the silly case where you have two of the same monitor and the color profiles have switched ( you see the _left profile loading on the right) go back into the applet and switch the profiles.

TADA…your done ....email me or post comments on any problems/questions

After buying a second 22”Samsung LCD 226BW. I bought the first one around a year ago, right in the middle of the big panel debate (if you don’t know what I’m talking about search for that model monitor and “S panel”.) Basically Samsung outsourced its panels to a few other manufacturers and while they weren’t “bad” monitors, the Samsung made panels were far better. I got lucky and my original monitor turned out to be a S panel and I have been insanely happy with it.

Flash forward to now, I order a second monitor and receive an “A panel”. While the monitor is very good quality, no stuck pixels, etc there is one problem. The monitor has a SEVERE blue tint to it under normal setup. Using the built in color adjustment I robbed the monitor of almost all blue color, from a setting of “50” to a setting of “5” and there was still a pronounced blue tint. Doing what any normal person would do I decided to spend more money and get a monitor color calibrator.

I wasn’t aware they had dropped so greatly in price, and after searching Amazon.com I ordered this Spyder2Express.

Now after ordering I noticed a serious problem, this product only works on a single monitor. You need the $160 device to support dual monitors. So after a little searching and a little playing I figured out there are ways around it. So here I’m going to outline how to use this with dual monitors on Windows Vista and XP.

PreReq’s :

Windows Vista comes with a built in utility to manage color profiles where as Windows XP does not. Usually color profiles end with a *.icm file extension. These are stored in x:\WINDOWS\System32\Spool\drivers\Color on both a Vista machine and an XP machine.

So if you have windows XP grab the “Microsoft Color Control Applet”, it can be found here Microsoft Color Control Applet and its provided straight from Microsoft. With this applet you get the same control that they now built into Vista. This applet gets installed into the Control Panel. So before you go and run a Spyder2Express there are some things you should know. First uninstall Adobe Gamma, or any type of color profile management software. Including the monitors software i.e. Samsung. After this you’re ready to run the color calibrator.

Living in both the design and computer world forces one to have both a PC and MAC. Commonly I'm back and forth to the pc to the mac and having two keyboards is a pain in the ass. Also shifting from typing on one board to the other get very annoying. One common solution is a KVM switch. This does not require the computers to be networked and will maximize my desk space. KVM's are pretty cheap but os x only runs USB keyboards so its necessary to have a USB to USB KVM. Most are PS2 which is fine PC to PC. After some fishing it comes up that the IOGEAR KVM GCS623U works perfect. You can pick it up at best buy for $70.99 or AMAZON for half the price.

The iogear's KVM was simple to set up, literally just plug in your keyboard and mouse and its switchign between the apple and pc when scroll lock is double tapped. Once installed I entered into hotkey mod (holding down the numlock key and holding the minus key for one second) and changed the double tap switch port key to CTRL. The KVM also supports VGA video and usb audio which is cool but not pratical in my situation. This KVM also saved a USB port since it combines the two peripherals into one USB plug. This is a bonus since there is only 3 ports on an iMac. The IOGEAR KVM GCS623U is an awesome investment if your stuck between Windows Xp and OS X.